Esta atualização de firmware para a camera SLT-A77V oferece os seguintes aperfeiçoamentos:
– Melhora a qualidade de imagem para a gravação do vídeo a 24p
– Melhora imagens superexpostas quando usa um controle para flash ADI
– Melhora a usabilidade
– Melhora as respostas para os mostradores dianteira / traseira quando atribuído para a compensação da exposição
– Compatibilidade com lentes as seguintes lentes com compensação automática:
– Vario-Sonnar T DT 16-80mm F3.5-4.5 ZA (SAL1680Z)
– DT 16-105mm F3.5-5.6 (SAL16105)
Download para Windows
Verifique a versão do firmware da câmera:
Follow the instructions below to check the firmware version of your camera.
If the firmware version is Ver.1.04 or later, the update is not required.
- Select Menu –> Setup –> Version on the camera.
- The firmware version is displayed as illustrated below.
Produtos suportados
This firmware update only applies to SLT-A77 that currently has a firmware version 1.03 or lower
Sistemas operativos compatíveis
- Windows XP* SP3
- Windows Vista** SP2
- Windows 7 SP1
Notes:
- * 64-bit and Starter editions are not supported.
- ** Starter edition is not supported.
Preparing for firmware update
- Computer hardware
- Hard disk space: 200MB or more
- RAM: 512MB or more
Note: Please close all other application software before updating the firmware.
- Power source for the camera
- Fully charged rechargeable battery pack NP-FM500H
or
AC adapter AC-PW10AM (sold separately)Note: The update can be performed only when the remaining battery level is (three marks) or more. We recommend that you use a fully charged battery or the AC adapter AC-PW10AM (sold separately).
- Fully charged rechargeable battery pack NP-FM500H
- USB cable supplied with the camera
Note: Update functionality is not guaranteed with any other USB cable.
Important notes:
- When performing the firmware update, please use a fully charged rechargeable battery pack NP-FM500H or the AC adapter AC-PW10AM (sold separately).
- Do not remove the battery or AC adapter during the update; otherwise, the camera may become inoperable due to the sudden power shutdown.
- Remove the memory card from the camera beforehand.
- Do not cover Eyepiece sensors (A.) during the update; otherwise, the LCD monitor may switch to the Viewfinder. If you can not see anything on the LCD monitor, please press the [FINDER / LCD button] (B.) .
Step 1: Reset your camera to the default settings
- Select Menu –> Setup –> Initialize on the camera.
- Select Reset Default .
- Select OK .
- Wait more than 10 seconds. (Do not care wether the LCD screen of the camera turns off, or not)
- Remove the power source ( battery or AC adaptor ) from the camera.
- Attach the power source ( battery or AC adaptor ) back to the camera.
Step 2: Download the firmware updater
- Make sure that you are logged on as a user with administrative rights.
- At the bottom of the page, read the disclaimer and agree to the terms and conditions by clicking on the checkbox. Then, click on the Download button.
- The download of the [Update_SLTA77V104.exe] file will start.
- Save the file to the desktop of your computer (recommended).
Step 3: Start up the Firmware Updater
- Close all currently running programs on your computer.
- Double-click the [Update_SLTA77V104.exe] file you downloaded to start up the Firmware Updater.
The Firmware Updater window appears. - According to the instruction on the Firmware Updater window, select Menu –> Setup –> USB Connection on the camera, and check if Mass Storage is selected.
If another mode than Mass Storage is selected, please select Mass Storage . - If it has not been done already, remove the memory card from the camera.
- Connect the camera to the computer with the supplied USB cable.
Note: USB Mode appears on the LCD monitor of the camera. - Confirm the “Safely Remove Hardware” icon is displayed on the task tray at the lower right corner of the computer screen.
- After confirming the above, click Next on the Firmware Updater window. Figure 1 appears on the Firmware Updater window, and Figure 2 appears on the LCD screen of the camera.
- When clicking Next , do not cover Eyepiece sensors ( A. on Figure 2.1 ) during the update; otherwise, the LCD monitor may switch to the Viewfinder. If you can not see anything on the LCD monitor, please press the [FINDER / LCD button] ( B. on Figure 2.1 ).
- If Figure 2 does not appears on the LCD screen of the camera, please disconnect the USB cable from the camera, and proceed to the ” Recovery procedure ” detailed at the bottom of the page.
Note: From now on, never turn off the camera until the firmware update is completed.
Figure 1 Figure 2 Figure 2.1 - After confirming the screens on Figures 1 and 2, click Next . The current version and the version after the update appear on the lower left part of the screen. (Figure 3)
- After confirming Current Version is Ver.1.02 or Ver.1.03 , click Next .
If the screen on Figure 4 appears, the update is not required. According to the message, stop the USB connection and click Finish . Turn off the camera, remove the battery pack or the AC adapter, reinsert the battery or reconnect the AC adapter and turn on the camera.
Figure 3: Update is required.
Figure 4: Update is not required.
- Click the “Safely Remove Hardware” icon on the task tray at the lower right corner of the computer screen to stop the USB connection, as instructed on figure 5.
Note: Please keep the USB cable connected even after stopping the USB connection on the computer with the above operation.
Figure 5
- Press the center of the [Multi-selector] to execute the reset of the camera.
Note: The screen turns off when the center of the [Multi-selector] is pressed. Please proceed to the next step. - Click Next on the Firmware Updater window ( Figure 5 ).
- After resetting, reconnection of the camera is verified, and the screen on Figure 6 appears.
- Click Run to start the update. The progress bar appears while updating (approximately 5 minutes).
Note:Never turn off the camera nor disconnect the USB cable while updating.
Figure 6
- When the update is completed, the screen on Figure 7 appears. Click Finish and disconnect the USB cable.
Figure 7
- Turn off the camera, remove the battery pack or the AC adapter, reinsert the battery or reconnect the AC adapter and turn on the camera.
Step 4: Confirm the firmware version of your camera is Ver.1.04.
- Select Menu –> Setup –> Version on the camera.
- The firmware version is displayed as illustrated below.
Recovery procedure
If the USB connection was not successful, please follow the below instructions:
- Turn ON the camera.
- Press the MENU , Playback and MOVIE buttons simultaneously.
- While Pressing these buttons, turn OFF the camera.
- Release your fingers, and wait over 30 seconds.
- Press the MENU , Playback and MOVIE buttons simultaneously again.
- While Pressing these buttons, now turn ON the camera.
- Release your fingers.
After performing the above procedure, try to update again starting from Step 3.3 .